Experimental study of premixed gasoline surrogates burning velocities in a spherical combustion bomb at engine like conditions

Producción CientíficaIn this work are presented experimental values of the burning velocity of iso-octane/air, n-heptane/air and n-heptane/toluene/air mixtures, gasoline surrogates valid over a range of pressures and temperatures similar to those obtained in internal combustion engines. The present work is based on a method to determine the burning velocities of liquid fuels in a spherical constant volume combustion bomb, in which the initial conditions of pressure, temperature and fuel/air equivalence ratios can be accurately established. A two-zone thermodynamic diagnostic model was used to analyze the combustion pressure trace and calculate thermodynamic variables that cannot be directly measured: the burning velocity and mass burning rate. This experimental facility has been used and validated before for the determination of the burning velocity of gaseous fuels and it is validated in this work for liquid fuels. The values obtained for the burning velocity are expressed as power laws of the pressure, temperature and equivalence ratio. Iso-octane, n-heptane and mixtures of n-heptane/toluene have been used as surrogates, with toluene accounting for the aromatic part of the fuel. Initially, the method is validated for liquid fuels by determining the burning velocity of iso-octane and then comparing the results with those corresponding in the literature. Following, the burning velocity of n-heptane and a blend of 50% n-heptane and 50% toluene are determined. Results of the burning velocities of iso-octane have been obtained for pressures between 0.1 and 0.5 MPa and temperatures between 360 and 450 K, for n-heptane 0.1–1.2 MPa and 370–650 K, and for the mixture of 50% n-heptane/50% toluene 0.2–1.0 MPa and 360–700 K. The power law correlations obtained with the results for the three different fuels show a positive dependence with the initial temperature and the equivalence ratio, and an inverse dependence with the initial pressure. Finally, the comparison of the burning velocity results of iso-octane and n-heptane with those obtained in the literature show a good agreement, validating the method used. Analytical expressions of burning velocity as power laws of pressure and unburned temperature are presented for each fuel and equivalence ratio.Ministerio de Ciencia e Innovación (PID2019-106957RB-C22

Study of the cycle-to-cycle variations of an internal combustion engine fuelled with natural gas/hydrogen blends from the diagnosis of combustion pressure

Producción CientíficaSe presenta una metodología para el estudio de la influencia de la adicción de hidrógeno (de 0 a 100% en sustitución del gas natural en mezclas de gas natural/aire en la dispersión cíclica de la combustión de un motor de encendido provocado. Se utiliza un algoritmo genético que optimiza un modelo de diagnóstico de la combustión a partir de la presión medida experimentalmente en la cámara de combustión de forma que se optimizan entradas al modelo de diágnóstico como son el ángulo de la presión máxima y el offset de presión, la relación de compresión volumétrica, el índice de la transferencia de calor a las paredes, etc. Se observa que la adición de hidrógeno aumenta mucho la velocidad de combustión a partir de un valor del 60%.Ministerio de economía y competitividad de Españ

Characterization of the combustion process and cycle-to-cycle variations in a spark ignition engine fuelled with natural gas/hydrogen mixtures.

Producción CientíficaSe presenta un estudio de la influencia del dosado o relación combustible/aire y del régimen de giro de un motor de combustión interna alternativo sobre la combustión y la dispersión cíclica del motor de encendido provocado funcionando con mezclas de aire, gas natural e hidrógeno. Para ello se utilizan dos parámetros comúnmente utilizados y uno nuevo basado en la masa quemada y en la tasa de masa quemada. Para esto se utiliza un modelo de diagnóstico de la combustión a partir de la presión medida en la cámara de combustión, de forma que se determina la fracción de masa quemada. Posteriormente se utiliza un modelo de algoritmos genéticos de forma que se optimizan los principales parámetros del modelo de diagnóstico de forma objetiva y con exactitud, como son la posición angular y offset de la presión medida, la relación de compresión volumétrica y los coeficientes de transmisión de calor por las paredes. Se concluye que la dispersión cíclica es altamente dependiente del régimen de giro y muy poco del dosado

Characterization of cycle-to-cycle variations in a natural gas spark ignition engine

Producción CientíficaSe presenta un estudio de la influencia del dosado o relación combustible/aire y del régimen de giro de un motor de combustión interna alternativo sobre la dispersión cíclica del motor de encendido provocado funcionando con mezclas de aire y gas natural. Para ello se utilizan dos parámetros comúnmente utilizados y uno nuevo basado en la masa quemada y en la tasa de masa quemada. Para esto se utiliza un modelo de diagnóstico de la combustión a partir de la presión medida en la cámara de combustión, de forma que se determina la fracción de masa quemada. Posteriormente se utiliza un modelo de algoritmos genéticos de forma que se optimizan los principales parámetros del modelo de diagnóstico de forma objetiva y con exactitud, como son la posición angular y offset de la presión medida, la relación de compresión volumétrica y los coeficientes de transmisión de calor por las paredes. Se concluye que la dispersión cíclica es altamente dependiente del régimen de giro y muy poco del dosado.Ministerio de Ciencia, Innovación y Universidades (grant ENE2012-34830

Combustion and Flame Front Morphology Characterization of H2–CO Syngas Blends in Constant Volume Combustion Bombs

Producción CientíficaThe need to develop new, alternative, and bio-origin fuels for use in internal combustion engines has motivated the realization of this research, which aims to characterize the combustion process synthesis gas, represented by H2–CO blends, which are its main constituents. Syngas can be considered a biofuel because it is a mixture of carbon monoxide, hydrogen, and other hydrocarbons, and it is formed by partial combustion of biomass. Experimental tests have been developed in two constant volume combustion bombs with spherical and cylindrical geometries to analyze the combustion process and the influence of the blend composition on the burning velocity. In the first one, the pressure registered during the combustion has been used to obtain the mass burning rate, temperatures, and burning velocities. The cylindrical bomb has two optical accesses through which the combustion process can be visualized and recorded with the Schlieren technique, and it has been used to characterize the morphology of the flame, the evolution of the flame front, or the laminar burning velocities, among other parameters of interest in the combustion process. For initial conditions of 0.1 MPa and 300 K, blends with different compositions and equivalence ratios have been studied. The introduction of hydrogen enhances combustion velocity and pressure, introducing also instabilities visible on flame front images, similar effects to those produced by increasing the equivalence ratio. Regarding the morphology of the flames, note that the tend to wrinkle and the cellularity increases as the hydrogen content of the mixture increases and the equivalence ratio decreases. The dependence of the numerical values of burning velocity has been expressed as a correlation on pressure and temperature. Finally, comparing the results of the burning velocities obtained in the spherical bomb and in the cylindrical bomb with those of different authors of the bibliography has checked the consistency and validity of them. Results of syngas blends are essential for the validation, optimization, and development of kinetic models for combustion development.Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (grant PID2019-106957RB-C22

Association of narcolepsy-cataplexy with HLA-DRB1 and DQB1 in Mexican patients: A relationship between HLA and gender is suggested

<p>Abstract</p> <p>Background</p> <p>Narcolepsy-cataplexy is characterized by excessive daytime sleepiness with recurrent episodes of irresistible sleep, cataplexy, hallucinations and sleep paralysis. Its aetiology is unknown, but it is positively associated with the human leukocyte antigens (HLA) in all studied populations. The purpose of the present study was to investigate the association of HLA class II <it>DRB1</it>/<it>DQB1 </it>alleles with narcolepsy-cataplexy in Mexican Mestizo patients.</p> <p>Methods</p> <p>This is a case-control study of consecutive patients and ethnically matched controls. We included 32 patients diagnosed with typical narcolepsy-cataplexy, of the National Institute of Neurology, of the Institute of Psychiatry and at the Center of Narcolepsy at Stanford University. As healthy controls, 203 Mexican Mestizos were included. <it>DRB1 </it>alleles were identified using sequence based typing. A PCR-SSOP reverse dot blot was used for <it>DQB1 </it>typing. Allele frequency was calculated by direct counting and the significance of the differences was assessed using the Yates Chi square. Odds ratio and confidence intervals were evaluated.</p> <p>Results</p> <p>HLA-<it>DRB1</it>*1501 (OR = 8.2; pc < 0.0001) and <it>DQB1</it>*0602 (OR = 8.4; pc < 0.0001) were found positively associated with narcolepsy. When deleting <it>DQB1</it>*0602+ patients from the analysis, <it>DQB1</it>*0301 was also found increased (OR = 2.7; p = 0.035; pc = NS). <it>DQB1</it>*0602/<it>DQB1</it>*0301 genotype was present in 15.6% of the cases (OR = 11.5; p = 0.00035), conferring a high risk. <it>DRB1</it>*0407 (OR = 0.2; p = 0.016 pc = NS) and <it>DQB1</it>*0302(OR = 0.4; p = 0.017, pc = NS) were found decreased in the patients. The gender stratification analysis showed a higher risk in females carrying <it>DRB1</it>*1501 (OR = 15.8, pc < 0.0001) and <it>DQB1</it>*0602 (OR = 19.8, pc < 0.0001) than in males (OR = 5.0 for both alleles; p = 0.012, pc = NS for <it>DRB1 </it>& p = 0.0012, pc = 0.017 for <it>DQB1</it>). The susceptibility alleles found in Mexicans with narcolepsy are also present in Japanese and Caucasians; <it>DRB1</it>*04 linked protection has also been shown in Koreans. A stronger HLA association is suggested in females, in accordance with the sexual dimorphism claimed previously.</p> <p>Conclusion</p> <p>This knowledge may contribute to a better understanding of the disease pathogenesis in different populations. The evaluation of the risk to develop narcolepsy-cataplexy in carriers of the described alleles/genotypes may also be possible. A larger sample should be analysed in Mexican and in other Hispanic patients to confirm these results.</p

The CARBA-MAP study: national mapping of carbapenemases in Spain (2014–2018)

Introduction:Infections caused by carbapenem-resistant Enterobacterales (CRE) and carbapenem-resistant Pseudomonas aeruginosa, including isolates producing acquired carbapenemases, constitute a prevalent health problem worldwide. The primary objective of this study was to determine the distribution of the different carbapenemases among carbapenemase-producing Enterobacterales (CPE, specifically Escherichia coli, Klebsiella pneumoniae, Enterobacter cloacae complex, and Klebsiella aerogenes) and carbapenemase-producing P. aeruginosa (CPPA) in Spain from January 2014 to December 2018.Methods: A national, retrospective, cross-sectional multicenter study was performed. The study included the first isolate per patient and year obtained from clinical samples and obtained for diagnosis of infection in hospitalized patients. A structured questionnaire was completed by the participating centers using the REDCap platform, and results were analyzed using IBM SPSS Statistics 29.0.0.Results: A total of 2,704 carbapenemase-producing microorganisms were included, for which the type of carbapenemase was determined in 2692 cases: 2280 CPE (84.7%) and 412 CPPA (15.3%), most often using molecular methods and immunochromatographic assays. Globally, the most frequent types of carbapenemase in Enterobacterales and P. aeruginosa were OXA-48-like, alone or in combination with other enzymes (1,523 cases, 66.8%) and VIM (365 cases, 88.6%), respectively. Among Enterobacterales, carbapenemase-producing K. pneumoniae was reported in 1821 cases (79.9%), followed by E. cloacae complex in 334 cases (14.6%). In Enterobacterales, KPC is mainly present in the South and South-East regions of Spain and OXA-48-like in the rest of the country. Regarding P. aeruginosa, VIM is widely distributed all over the country. Globally, an increasing percentage of OXA-48-like enzymes was observed from 2014 to 2017. KPC enzymes were more frequent in 2017–2018 compared to 2014–2016.Discussion: Data from this study help to understand the situation and evolution of the main species of CPE and CPPA in Spain, with practical implications for control and optimal treatment of infections caused by these multi-drug resistant organisms

Innovación del Diseño para el Desarrollo Social

Una labor de síntesis alrededor de la gran temática de este libro que surge a partir de una serie de reflexiones y propuestas encaminadas desde la innovación del diseño para el desarrollo social, refleja una invitación al lector para enunciar a partir de su lectura nuevas discusiones sobre el quehacer del diseño con una perspectiva de innovación para este tipo de desarrollo, es pues este texto una invitación a enunciar nuevos retos y diálogos partiendo de reconocer al desarrollo social como uno de los pilares fundamentales desde la Organización de las Naciones Unidas (ONU) como parte fundamental para garantizar el mejoramiento de la vida de las personas. Desde la disciplina del diseño y retomado como eje para su discusión se pretendería establecer una serie de reflexiones y acciones que permitan atender situaciones para grupos minoritarios y vulnerables, así como apoyar esfuerzos encaminados a mejorar la calidad de vida de los integrantes de grupos y sociedades establecidas y recuperar el patrimonio cultural como parte fundamental de las identidades culturales y por tanto de la historia de la humanidad.A lo largo de la historia, el diseño, en cualquiera de sus manifestaciones, ha estado presente en todos los ámbitos. Se ha convertido en una disciplina que evoluciona al ritmo de las sociedades, que se pone al servicio de las necesidades de mercado pero también de las que requieren un abordaje distinto, observadas desde una mirada que concierne a lo social, entendido éste como lo que se reproduce o se instaura en el colectivo, en el grupo, en las comunidades, en las sociedades como parte significativa de sus cotidianeidades. El Diseño desde esta perspectiva acompaña al ser humano produciendo una significación de los objetos como parte fundamental de sus vidas, que transforma una realidad deseada en una realidad concreta, de aquí la importancia de crear una conciencia social para la praxis laboral de esta disciplina. En este sentido el campo profesional, académico y de investigación del diseño debe ocuparse de crear, difundir y divulgar el quehacer de la misma, manifestando un equilibrio entre conciencia, racionalidad y la realidad. Desde el contexto planteado, la Universidad Autónoma del Estado de México, a través de su Facultad de Arquitectura y Diseño presenta en esta obra una serie de reflexiones en torno al papel que desempeña el diseño humanístico, científico y tecnológico desde un enfoque de vanguardia e innovación para el desarrollo social, como resultado de la experiencia vertida en el Coloquio Internacional de Diseño que organiza éste año este espacio académico, en donde cada una de las aportaciones refleja la experiencia de cada uno de sus participantes; con base en ello, el presente libro integrado por una compilación de trabajos ofrece descripciones, análisis y propuestas que contribuyen a la solución de problemas procurando un desarrollo social

Mortality and pulmonary complications in patients undergoing surgery with perioperative SARS-CoV-2 infection: an international cohort study

Background: The impact of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) on postoperative recovery needs to be understood to inform clinical decision making during and after the COVID-19 pandemic. This study reports 30-day mortality and pulmonary complication rates in patients with perioperative SARS-CoV-2 infection. Methods: This international, multicentre, cohort study at 235 hospitals in 24 countries included all patients undergoing surgery who had SARS-CoV-2 infection confirmed within 7 days before or 30 days after surgery. The primary outcome measure was 30-day postoperative mortality and was assessed in all enrolled patients. The main secondary outcome measure was pulmonary complications, defined as pneumonia, acute respiratory distress syndrome, or unexpected postoperative ventilation. Findings: This analysis includes 1128 patients who had surgery between Jan 1 and March 31, 2020, of whom 835 (74·0%) had emergency surgery and 280 (24·8%) had elective surgery. SARS-CoV-2 infection was confirmed preoperatively in 294 (26·1%) patients. 30-day mortality was 23·8% (268 of 1128). Pulmonary complications occurred in 577 (51·2%) of 1128 patients; 30-day mortality in these patients was 38·0% (219 of 577), accounting for 81·7% (219 of 268) of all deaths. In adjusted analyses, 30-day mortality was associated with male sex (odds ratio 1·75 [95% CI 1·28–2·40], p\textless0·0001), age 70 years or older versus younger than 70 years (2·30 [1·65–3·22], p\textless0·0001), American Society of Anesthesiologists grades 3–5 versus grades 1–2 (2·35 [1·57–3·53], p\textless0·0001), malignant versus benign or obstetric diagnosis (1·55 [1·01–2·39], p=0·046), emergency versus elective surgery (1·67 [1·06–2·63], p=0·026), and major versus minor surgery (1·52 [1·01–2·31], p=0·047). Interpretation: Postoperative pulmonary complications occur in half of patients with perioperative SARS-CoV-2 infection and are associated with high mortality. Thresholds for surgery during the COVID-19 pandemic should be higher than during normal practice, particularly in men aged 70 years and older. Consideration should be given for postponing non-urgent procedures and promoting non-operative treatment to delay or avoid the need for surgery. Funding: National Institute for Health Research (NIHR), Association of Coloproctology of Great Britain and Ireland, Bowel and Cancer Research, Bowel Disease Research Foundation, Association of Upper Gastrointestinal Surgeons, British Association of Surgical Oncology, British Gynaecological Cancer Society, European Society of Coloproctology, NIHR Academy, Sarcoma UK, Vascular Society for Great Britain and Ireland, and Yorkshire Cancer Research

Guidelines for the use and interpretation of assays for monitoring autophagy (3rd edition)

In 2008 we published the first set of guidelines for standardizing research in autophagy. Since then, research on this topic has continued to accelerate, and many new scientists have entered the field. Our knowledge base and relevant new technologies have also been expanding. Accordingly, it is important to update these guidelines for monitoring autophagy in different organisms. Various reviews have described the range of assays that have been used for this purpose. Nevertheless, there continues to be confusion regarding acceptable methods to measure autophagy, especially in multicellular eukaryotes. For example, a key point that needs to be emphasized is that there is a difference between measurements that monitor the numbers or volume of autophagic elements (e.g., autophagosomes or autolysosomes) at any stage of the autophagic process versus those that measure fl ux through the autophagy pathway (i.e., the complete process including the amount and rate of cargo sequestered and degraded). In particular, a block in macroautophagy that results in autophagosome accumulation must be differentiated from stimuli that increase autophagic activity, defi ned as increased autophagy induction coupled with increased delivery to, and degradation within, lysosomes (inmost higher eukaryotes and some protists such as Dictyostelium ) or the vacuole (in plants and fungi). In other words, it is especially important that investigators new to the fi eld understand that the appearance of more autophagosomes does not necessarily equate with more autophagy. In fact, in many cases, autophagosomes accumulate because of a block in trafficking to lysosomes without a concomitant change in autophagosome biogenesis, whereas an increase in autolysosomes may reflect a reduction in degradative activity. It is worth emphasizing here that lysosomal digestion is a stage of autophagy and evaluating its competence is a crucial part of the evaluation of autophagic flux, or complete autophagy. Here, we present a set of guidelines for the selection and interpretation of methods for use by investigators who aim to examine macroautophagy and related processes, as well as for reviewers who need to provide realistic and reasonable critiques of papers that are focused on these processes. These guidelines are not meant to be a formulaic set of rules, because the appropriate assays depend in part on the question being asked and the system being used. In addition, we emphasize that no individual assay is guaranteed to be the most appropriate one in every situation, and we strongly recommend the use of multiple assays to monitor autophagy. Along these lines, because of the potential for pleiotropic effects due to blocking autophagy through genetic manipulation it is imperative to delete or knock down more than one autophagy-related gene. In addition, some individual Atg proteins, or groups of proteins, are involved in other cellular pathways so not all Atg proteins can be used as a specific marker for an autophagic process. In these guidelines, we consider these various methods of assessing autophagy and what information can, or cannot, be obtained from them. Finally, by discussing the merits and limits of particular autophagy assays, we hope to encourage technical innovation in the field